“CNC全自动数控洗物盆滚焊机”参数说明
认证: | ISO9001 | 品牌: | 德力 |
驱动方式: | 自动 | 电流: | 直流 |
动力形式: | 水焊 | 类型: | 专机定制 |
用途: | 缝焊 | 作用对象: | 金属 |
焊接形式: | 688 | 成形时间: | 688 |
焊接直径: | 688 | 焊接能力: | 688 |
焊接速度: | 688 | 焊接压力: | 688 |
型号: | CNC | 规格: | 688 |
商标: | 688 | 包装: | 688 |
Mm: | Mm |
“CNC全自动数控洗物盆滚焊机”详细介绍
CNC全自动数控洗物盆滚焊机
、整机说明三、Machine instructions根据贵公司工件的特点,焊缝为同一平面上的曲线,采取四个电机四轴联合控制进行焊接。焊接时工件由水槽滑台上的专用下电极模具定位,水槽滑台左右移动,上电极滚轮上下加压、前后移动、旋转角度,按预设程序四轴联动走出焊缝轨迹,从而实现对工件焊接。除装卸工件人工外,整个焊接过程全自动,是理想的自动焊接设备。According equipment.● 机座:钢结构焊接而成,并经时效处理,保证长期使用不变形;焊接电源:采用MD-40KA中频逆变电源;控制系统:采用中频控制箱配合CNC联系动作。● Control system:Use medium frequency control box with CNC related action.● X轴:用来使得工件及平台能左右两侧来回往复移动;Y轴:用来使得上滚焊机头能前后方向来回往复移动;Z轴:用来使上滚焊机头上下移动,并产生焊接压力;U轴:用来使得上滚焊机头轴能够任意带动滚轮转动。伺服电机驱动,滚珠丝杠、直线运动导轨副。and 控制柜:采用三菱CNC控制系统。 head weld four points on the four corners destined position of the right of Sink Barrel (6S)→四轴联动,按预定轨道对右盆桶实施滚焊一圈(40s)→Four axis linkage,according to the orbit,rolling weld a circle for right sink barrel (40S)→四轴联动,上滚焊机头在左盆桶四角预定位置点焊四点(6s)→Four axis linkage,up rolling welder head weld four points on the four corners destined position of the left of Sink Barrel(6s)→四轴联动,按预定轨道对左盆桶实施滚焊一圈(40s)→Four axis linkage,according to the orbit,rolling weld a circle for left sink barrel (40S)→上机头、定位吸盘复位(0.5s)→Up head, positioning sucker reset(0.5s)→取工件(3s)→Take workpiece(3s)→装新工件并开始新的焊接。→Load new workpiece and began to the new welding焊接一个工件两个1500mm长焊缝盆桶预计用时约101s。Welding a workpieces which is two 1500mm length welding sink barrels estimate that it will take approximately 101s五、主要技术参数:五、Main Technical Parameter1. 输入电压: 380±10%(三相) 50HZ1.Input voltage: 380±10%(3-phase) 50HZ2. 输入功率: 90KVA2.Input power: 90KVA3. 次级电压: 12.7V3.Secondary voltage:12.7V4. 最大焊接电流:40KA4.Max welding current:40KA5. 负载持续率: 50%5.Rated duty cycle :50%6. 绝缘电阻: 输入电源对机身绝缘电阻≥2.5MΩ6.Insulation resistance:Insulation resistance between input power for the body ≥2.5MΩ7. 工作环境: 温度≤40℃,湿度≤90%7.Working environment: Temperature≤40℃, Humidity≤90%8. 最大工作压力:7200N8.Maximum working pressure:7200N9. 气源压力: 0.6-0.8MPa9.Gas pressure:0.6-0.8MPa10. 水源压力: 0.15MPa~0.25MPa(纯净水)10.Water pressure:0.15MPa~0.25MPa(pure water)11. 水流量: 40L/MIN11.Water flow rate: 40L/MIN
、整机说明三、Machine instructions根据贵公司工件的特点,焊缝为同一平面上的曲线,采取四个电机四轴联合控制进行焊接。焊接时工件由水槽滑台上的专用下电极模具定位,水槽滑台左右移动,上电极滚轮上下加压、前后移动、旋转角度,按预设程序四轴联动走出焊缝轨迹,从而实现对工件焊接。除装卸工件人工外,整个焊接过程全自动,是理想的自动焊接设备。According equipment.● 机座:钢结构焊接而成,并经时效处理,保证长期使用不变形;焊接电源:采用MD-40KA中频逆变电源;控制系统:采用中频控制箱配合CNC联系动作。● Control system:Use medium frequency control box with CNC related action.● X轴:用来使得工件及平台能左右两侧来回往复移动;Y轴:用来使得上滚焊机头能前后方向来回往复移动;Z轴:用来使上滚焊机头上下移动,并产生焊接压力;U轴:用来使得上滚焊机头轴能够任意带动滚轮转动。伺服电机驱动,滚珠丝杠、直线运动导轨副。and 控制柜:采用三菱CNC控制系统。 head weld four points on the four corners destined position of the right of Sink Barrel (6S)→四轴联动,按预定轨道对右盆桶实施滚焊一圈(40s)→Four axis linkage,according to the orbit,rolling weld a circle for right sink barrel (40S)→四轴联动,上滚焊机头在左盆桶四角预定位置点焊四点(6s)→Four axis linkage,up rolling welder head weld four points on the four corners destined position of the left of Sink Barrel(6s)→四轴联动,按预定轨道对左盆桶实施滚焊一圈(40s)→Four axis linkage,according to the orbit,rolling weld a circle for left sink barrel (40S)→上机头、定位吸盘复位(0.5s)→Up head, positioning sucker reset(0.5s)→取工件(3s)→Take workpiece(3s)→装新工件并开始新的焊接。→Load new workpiece and began to the new welding焊接一个工件两个1500mm长焊缝盆桶预计用时约101s。Welding a workpieces which is two 1500mm length welding sink barrels estimate that it will take approximately 101s五、主要技术参数:五、Main Technical Parameter1. 输入电压: 380±10%(三相) 50HZ1.Input voltage: 380±10%(3-phase) 50HZ2. 输入功率: 90KVA2.Input power: 90KVA3. 次级电压: 12.7V3.Secondary voltage:12.7V4. 最大焊接电流:40KA4.Max welding current:40KA5. 负载持续率: 50%5.Rated duty cycle :50%6. 绝缘电阻: 输入电源对机身绝缘电阻≥2.5MΩ6.Insulation resistance:Insulation resistance between input power for the body ≥2.5MΩ7. 工作环境: 温度≤40℃,湿度≤90%7.Working environment: Temperature≤40℃, Humidity≤90%8. 最大工作压力:7200N8.Maximum working pressure:7200N9. 气源压力: 0.6-0.8MPa9.Gas pressure:0.6-0.8MPa10. 水源压力: 0.15MPa~0.25MPa(纯净水)10.Water pressure:0.15MPa~0.25MPa(pure water)11. 水流量: 40L/MIN11.Water flow rate: 40L/MIN